Product Overview
A new type of heater has been developed by a customized manufacturer of 1200w 220V HSRY2-2220V/2KW hydraulic oil heater, based on the advantages of various direct heaters at home and abroad. It has the advantages of good noise reduction, low vibration, simple structure, and easy installation. And it saves energy, with a heat utilization rate of over 98%, suitable for all occasions where steam is used to prepare hot water and boiled water in food, chemical and other industries.
Details
Customized manufacturer of HSRY2-2220V/2KW hydraulic oil heater
Precautions for motor heater 1200w 220v
1. The component is allowed to operate under the following conditions:
A. The relative humidity of the air is not greater than 95%, and there are no explosive or corrosive gases. (Excluding explosion-proof heaters)
B. The working voltage should not exceed 1.1 times the rated value, and the casing should be effectively grounded.
C. Insulation resistance ≥ 1M Ω, dielectric strength: 2KV/1min.
2. Electric heating tubes should be properly positioned and fixed, and the effective heating area must be completely immersed in liquid or metal solids. Empty burning is strictly prohibited. When scale or carbon deposits are found on the surface of the pipe body, they should be removed and reused in a timely manner to avoid affecting heat dissipation and shortening the service life.
3. When heating molten metals or solid nitrate, alkali, asphalt, paraffin, etc., the operating voltage should be reduced first, and only after the medium melts can it be raised to the rated voltage.
4. When heating air, the components should be arranged in a cross and even manner to provide good heat dissipation conditions, so that the air flowing through can be fully heated.
5. When heating nitrate, safety measures should be considered to prevent explosion accidents.
6. The wiring part should be placed outside the insulation layer to avoid contact with corrosive, explosive media, and moisture; The lead wire should be able to withstand the temperature and heating load of the wiring part for a long time, and excessive force should be avoided when tightening the wiring screws.
7. The components should be stored in a dry place. If the insulation resistance is lower than 1M Ω due to long-term storage, they can be dried in an oven at around 200 ℃ or heated with reduced voltage until the insulation resistance is restored.
8. The magnesium oxide powder at the outlet of the electric heating tube should be protected from pollutants and moisture infiltration in the usage area to prevent leakage accidents.
Customized manufacturer of HSRY2-2220V/2KW hydraulic oil heater
Installation requirements for motor heater 1200w 220v
1. When using a steam silencing heater, it must be submerged at least 300mm below the water surface and placed at the geometric center of the container, with a distance of not less than 200mm from the side walls and bottom of the container.
2. When selecting, the diameter of the pipeline should be greater than or equal to the nominal diameter of the heater. When multiple heaters are used in parallel, the cross-sectional area of the steam pipeline should be greater than or equal to the sum of the cross-sectional areas of all heater connecting pipes.
3. When the steam pressure is greater than 0.5 MPa (gauge pressure), a steam pressure reducing valve should be installed to reduce the pressure, and a filter should be installed in front of it.
4. A check valve must be installed near the heater on the steam pipeline to prevent siphon phenomenon and water backflow accidents during steam shutdown.
5. The steam pipe near the heater should be securely fixed to prevent swinging during operation.
6. Multiple heaters should be used in parallel and evenly distributed. Due to their heavy weight, they should be supported and installed according to the site conditions.
7. The water temperature and level of the water tank should be measured and controlled using temperature and water level controllers.
8. If the heating speed of the heater slows down during use, it may be due to the blockage of its internal steam holes. The heater should be removed to remove impurities from the blocked steam holes, and the dirt should be discharged from the drain outlet. The heater should be cleaned once a month.